Mr-Glass Custom & Geometric Windows Nationwide | Winslow Windows & Doors

Mr-Glass Custom & Geometric Windows in Fort Myers: What to Know First

We provide independent Mr-Glass custom & geometric window repair and installation in Fort Myers, with most service calls completed in one visit and honest pricing quoted before we touch a single pane. As an independent Mr-Glass service provider, we work on the full range of shaped windows: arched, circular, elliptical, trapezoid and oversized geometric openings that make Florida homes stand out. Typical custom window service runs $180 to $800 depending on glass type, shape complexity and whether the sash or frame needs rebuilding. If you own a Mr-Glass window in Fort Myers and something’s off, call (239) 453-7751 for a straight answer.

Call (239) 453-7751

This page is for homeowners who have Mr-Glass windows that don’t fit the standard rectangle category: the arch over the front door, the eyebrow window in the gable, the angled trapezoid flanking a cathedral ceiling. These windows carry different stress loads than square units, and in Fort Myers, where a summer afternoon thunderstorm can drop an inch of rain in twenty minutes and hurricane season runs half the year, a geometric window with a failing seal or warped frame isn’t a cosmetic annoyance. It’s a water intrusion point.

How Mr-Glass Products Fail - and How We Fix Them

After years working on Mr-Glass windows across Fort Myers, we know exactly where these units give out first. Here’s what we see on service calls:

• Radius-unit seal failure at the springline. Arched and curved Mr-Glass units tend to lose their insulated glass seal right at the springline, the point where the straight side wall transitions into the curve. The radius puts constant tension on the sealant there, and Fort Myers heat expands and contracts that bond daily. You’ll see fogging that starts at the curve edges and creeps inward. We replace the insulated glass unit (IGU) and re-seat it with a sealant rated for curved geometry, not the flat-stock caulk some shops use.
• Trapezoid frame racking on older wood-clad Mr-Glass windows. We see this most on Mr-Glass’s wood-clad series installed in 1990s and early 2000s Fort Myers homes. Trapezoid and angled units concentrate corner stress differently than rectangles, and once the corner joinery loosens, the sash binds and the weep system clogs. We pull the sash, re-square the frame corners, re-bed the glass, and replace the corner keys with reinforced hardware.
• Eyebrow window hinge wear causing visible sag. Mr-Glass eyebrow windows are beautiful, but the curved top rail puts uneven load on the operating hinges. After ten-plus years of Fort Myers humidity and daily use, the sash sags by an eighth of an inch or more, and you’ll see daylight at the top curve. We replace the factory-style hinges with a matched set, re-balance the sash, and adjust the strike points. On units beyond hinge repair, we rebuild the sash carrier rather than forcing a new window into an opening that was never square to begin with.
• Impact-glazed geometric units with delamination at compound curves. Mr-Glass impact windows in true compound curves (like a full round with a flattened bottom) occasionally show interior lamination lines after major storms. This isn’t glass fracture; it’s the laminate interlayer separating where the curvature is tightest. We inspect with a light test to confirm it’s cosmetic versus structural, document it for warranty purposes when applicable, and replace the IGU when the separation crosses into the visible field or compromises the impact rating.
• Oversized fixed geometric windows with failing structural glazing tape. Large Mr-Glass picture-type geometric openings, especially gable apexes and half-rounds over entryways, rely on structural glazing tape to hold the unit in the opening. In Fort Myers, that tape breaks down faster than in drier climates, and once it loses adhesion, the unit shifts slightly with pressure changes. You’ll hear a faint clicking in windy weather or notice the caulk line cracking where the glass meets the frame. We pull the unit, clean the opening to bare substrate, apply new structural tape rated for the glazing weight, and reset with new interior stops.

Our Mr-Glass Custom & Geometric Windows Process

1. 1
   You call, a person answers. Day or night, you get a live voice at (239) 453-7751. We ask about the window shape, its location, and what you’re seeing. Then we schedule a visit that fits your calendar, not ours.
2. 2
   On-site diagnosis with a window-by-window check. Our tech arrives in uniform, background-checked, and puts eyes on the actual unit. We measure the radius, check the seal from inside and out, test the operation, and photograph the failure points so you see what we see.
3. 3
   Parts decision: OEM when it matters, aftermarket when it’s better. For Mr-Glass hardware that’s still in production, we source original spec parts. For legacy units where OEM availability is spotty, we use aftermarket components that meet or exceed the original rating, and we tell you exactly what we’re using and why before we order anything.
4. 4
   The repair or replacement, done in place. We don’t yank a geometric window out and hope a stock rectangle fits. We work the existing opening, rebuilding frames, re-bedding glass, and re-balancing sashes so the finished window sits square, seals tight, and operates smoothly.
5. 5
   Water test and daylight inspection. Before we pack up, we run a water test on the exterior and a daylight/compression check on the weatherstripping. If air or water sneaks through, we’re not done.
6. 6
   The 36500-Day Done Right Promise. If it’s not right, we come back and make it right. That’s a hundred-year standard on paper, but in practice it means we treat every custom window job like Ed’s checking it personally. Because he is.

What Mr-Glass Custom & Geometric Windows Costs in Fort Myers

Straight numbers, because that’s how we work. Here’s what Mr-Glass custom and geometric window service typically runs in Fort Myers:

• IGU replacement on a single arched or radius window: $280 to $650, depending on glass package (clear, low-E, or impact) and radius tightness.
• Full sash rebuild on a trapezoid or angled operating window: $350 to $800, including corner reinforcement and new hardware.
• Hinge replacement and re-balance on an eyebrow window: $180 to $420, including adjustment and weatherstripping renew.
• Full custom geometric unit replacement (large fixed gable or entry half-round): $950 to $2,800, depending on size, glass type, and whether the frame needs re-roughing.
• Diagnostic visit (no repair): No trip charge inside our home county. You pay nothing just to have us look and tell you the truth.

What moves the price: compound curvature (tighter radius costs more to fabricate), impact glazing versus standard tempered, and whether the frame needs structural repair or just re-bedding. Every estimate is a written line-item quote, and the number on that paper is the number on the invoice. Call (239) 453-7751 for your free estimate. If you already have a written estimate from another company, bring it. We’ll give you a second opinion free.

Why Fort Myers Homeowners Call Winslow Windows & Doors for Mr-Glass Work

We’ve been serving Fort Myers since 2011, and Ed Winslow’s name is on the door, literally. That means every Mr-Glass custom window we service or install has to be right, or we come back. It’s the 36500-Day Done Right Promise, and it isn’t a marketing line. It’s how we’ve operated for over fifteen years, and it’s why homeowners from McGregor Boulevard to the Caloosahatchee call us when a geometric window stops behaving.

When your Mr-Glass arch or trapezoid window fails, you don’t want a call center that files a ticket. You want a tech who knows why the springline seal gave out and has the right part on the truck. Our technicians are background-checked, uniformed, and trained on Mr-Glass geometry, and they’ve all been through Fort Myers storm seasons where poorly sealed custom windows show their weaknesses fast. If a unit is beyond reasonable repair, we’re authorized installers for PGT, CGI, CWS, ES Windows and other premium replacement lines, so we can match a custom opening with a properly engineered replacement rather than forcing a stock size into a geometric hole.

We answer the phone 24/7. We give you upfront pricing, a free second opinion on any written estimate, $40 off any repair over $200, no trip charge inside Lee County, and a permanent 10% discount for seniors and veterans. Ed’s name is on the truck, and every job we do has to live up to that.

FAQs